WA Quick Help
⚡ QUICK WHATSAPP ESTIMATE
Prestige Paint

How to Paint Doors, Frames and Skirting in a Nigerian Home

Doors, frames and skirting take more punishment than any wall in the house. A door is pushed by every hand that passes through it. Skirting takes shoes, mops and the vacuum. Frames sit in the gap where two materials move at different rates.

They also fail differently from walls. A wall fails by fading or flaking over years; a door fails at the edges, along the bottom, and around the handle. Which is why painting them is a different job, with different preparation and a different finish.

Why the edges go first

A painted door has four surfaces taking wear at once. The face is touched by hands. The leading edge is knocked by rings, keys and whatever is carried through. The bottom edge takes water every time the floor is mopped. The lock area is gripped dozens of times a day, and hand grease dissolves a cheap paint film over a couple of years.

Outside doors add sun and rain to that list. In Nigeria an exterior door faces intense ultraviolet light on one side and driving rain on the other, and the paint on it expands and contracts twice as much as the wall around it.

So the failures you see are predictable: chipped edges, a dark band along the bottom, yellowing gloss, and a handle area that has gone sticky and dull.

Choosing the finish

Interior doors and skirting want a finish that can be wiped. Prestige Satin Finish is the practical choice for most interiors: hard enough for a wet cloth and a mild detergent, low enough sheen that it does not show every mark.

Prestige Premium Plus Gloss is the harder film, and the right choice where the door takes real traffic or faces the weather. Gloss shows imperfections, though, so it suits a flat door far better than a panelled one that has been filled and sanded a dozen times.

Two rules that save trouble. Do not put a matt emulsion on a door, whatever the colour card says: it marks, it cannot be scrubbed, and it will need redoing within a year. And do not paint a front door in a colour so light that hand marks show within a month.

Preparation is most of the job

Remove the handle, lock, letter plate and any hooks. Masking tape around them is faster and always looks worse afterwards, because paint bridges the tape line and lifts when the tape comes off.

Wash the surface with a degreaser, paying attention to the handle side and the edges. Paint will not bond to hand grease, and a door painted over grease will fail exactly where it is touched most.

Then sand. On sound old paint, a light key is enough: the new coat needs something to grip. On chipped or flaking paint, sand back to a firm edge, because a new coat over a loose edge lifts it within months.

Fill dents, old screw holes and splits with Prestige Super Filler, slightly proud, then sand flush once dry. On bare pine, seal the knots: resin bleeds through paint as a brown stain that no number of coats will cover.

Prime anything bare. Bare wood takes paint unevenly and shows grain through the finish; bare metal needs a metal primer for both adhesion and corrosion. An MDF door needs its cut edges sealed, because they drink paint and stay rough however many coats you apply.

Finally, dust off. Filler dust is the single most common cause of a coat that peels.

The order to paint a door

  1. Paint the mouldings and panel edges first, then the flat panels, working from the top down
  2. Paint the stiles and rails, the vertical and horizontal frame pieces
  3. Finish with the door edges, top and bottom
  4. On a flat door: the top edge, then the two sides, then the face in long strokes, finishing with light vertical passes to lay off the brush marks

Two thin coats always beat one thick coat. A thick coat skins over while the paint underneath is still wet, and it will wrinkle or stay soft for weeks. Keep a wet edge as you work and avoid going back over paint that has started to set, which is what leaves brush marks.

Skirting, architraves and the wall joint

Skirting is where a room looks finished or looks rushed. The joint between skirting and wall is never perfectly straight, and it moves. Run a bead of paintable acrylic caulk along it before painting, smooth it with a damp finger, and let it cure. That one line removes the dark shadow gap that makes a repaint look unfinished.

Cut in along the top edge with a brush rather than relying on tape. Tape lifted off fresh paint takes a strip of the paint with it; if you do use it, pull it while the paint is still tacky, not after it has cured.

Keep a damp cloth with you. Paint on a tile or a floor is far easier to remove in the first minute than the next morning.

Metal gates, frames and railings

Metal is a different job. Rust has to come off before anything goes on: wire brush or sand to bare metal, treat what is left, then a metal primer, then the gloss. Paint over rust and it keeps rusting underneath until it pushes the film off.

Mask hinges, locks and any moving part. Painted hinges bind, and a gate that will not close is a worse problem than a chipped edge.

The first week matters

Doors painted in gloss need air. Leave them ajar for a day or two rather than closing them tight while the film is still soft, because a door closed onto tacky paint sticks, and pulling it open takes the paint with it.

Do not wash the surfaces for a couple of weeks. A gloss film hardens over days, not hours, and washing early dulls it and shortens its life.

Mistakes that show within the year

  • No primer on bare wood, so the grain shows through and the coat dries patchy
  • Painting over chipped gloss without sanding, so the edges lift
  • One thick coat instead of two thin ones
  • Painting the hinges, locks and strike plates
  • Painting late in the evening in humid weather, which leaves a milky bloom on gloss
  • Using matt emulsion on a door because the colour matched

Getting it right the first time

If you are repainting a whole house, doors, frames and skirting are the parts that make the difference between a job that looks professional and one that looks like a DIY weekend. They are also the parts most people rush at the end of a project, when the paint is running low and patience is shorter.

Buy the right primer and the right finish, allow two days for a house’s worth of doors and trim, and work in the order above. Call +234 802 562 5333 or message us on WhatsApp and tell us how many doors and how much skirting you have; we will tell you what quantities to buy and which finish suits the traffic.