WA Quick Help
⚡ QUICK WHATSAPP ESTIMATE
Prestige Paint

Damp Walls in Nigeria: Find the Cause Before You Paint

Almost every wall that fails in a Nigerian house fails because of water. Paint gets blamed, and the paint is usually the last thing involved. The water arrives from somewhere, sits in the plaster, and pushes the film off from behind.

Which means the most expensive mistake in decorating is also the simplest: painting over damp. It looks like a fix for a few weeks and then the stain returns, the paint blisters, and the mould comes back through the new finish.

Three sources, three different patterns

Damp is not one problem. It is at least three, and they are told apart by where they appear and when.

Rising damp comes up from the ground through the base of the wall. It shows as a band along the bottom, usually up to about a metre, and it is often worse after the rains. It happens where there is no damp-proof course, where the course has failed, or where something outside has bridged it, such as soil piled against the wall or a concrete path laid above the original level.

Penetrating damp comes through the wall from outside. It appears in patches, usually on an external wall, and it gets worse during and after rain. Common causes are a cracked render, a failed flashing, a leaking roof, a blocked gutter or a downpipe discharging against the wall.

Condensation is different: the water comes from inside the house. It shows on cold surfaces, in corners, behind furniture, and on ceilings in bathrooms and kitchens. It is worst in the rainy season and in rooms with poor ventilation, and it is the usual explanation for black mould in a room that has never had a leak.

A fourth case deserves its own line because it is missed most often: a plumbing leak. A slow leak in a pipe inside a wall shows as damp with no weather pattern at all.

How to tell them apart

Three questions cut through most of it:

  • Where is it? A band at the base suggests rising damp. A patch high on an external wall suggests penetration. Corners, ceilings and cold external walls suggest condensation
  • When is it worst? After rain means penetration. All year round means rising damp or a pipe. Worse in humid weather and in the mornings means condensation
  • What does it look like? Tide marks and a white salt bloom suggest water moving through the wall. Black speckled mould suggests condensation. Soft, crumbling plaster at low level suggests prolonged rising damp

Getting this wrong is expensive, because the fix for condensation is ventilation and the fix for rising damp is a building repair. No paint solves either.

Why painting over damp fails

Paint is a film. Once it cures it resists water from the front, which is what you want in a bathroom. Trapping water behind it is the opposite of what you want in a damp wall.

Water moving through plaster carries salts. When it reaches the back of a paint film it cannot pass, so the salts crystallise there and push the film off. That is why a damp wall often blisters in a pattern that follows the damp, not the brush strokes.

Mould works the same way. Painting over mould without killing it seals spores into the surface, and they grow back through the new film within a season.

What has to happen first

  1. Find and fix the source: the leak, the cracked render, the failed flashing, the bridged damp course, or the ventilation
  2. Let the wall dry. This takes weeks, not days, and the wall has to be exposed to air
  3. Remove the damaged finish: any blown plaster, flaking paint and soft filler
  4. Treat the mould with a proper mould treatment, not just bleach on the surface, and let it dry
  5. Repair the plaster and let the repair cure fully
  6. Prime the repaired areas, then paint

Skipping step two is where most jobs go wrong. A wall that has been wet for months will still be wet in the middle after a week of looking dry.

How to know a wall is ready

The reliable test is the same one used on new plaster: tape a square of clear plastic tight to the wall, leave it for a day, and look for condensation on the inside. Any moisture means the wall is still giving off water and painting will fail.

A moisture meter settles it properly. Any builder or surveyor has one, and five minutes with it is cheaper than a repaint.

What paint can and cannot do

Paint can resist moisture on the surface once the cause is fixed. A washable finish in a bathroom is a good example: it protects the wall from steam and lets you clean it.

Paint cannot hold back water arriving from behind. No product is a substitute for a damp course, a repaired roof or a working extractor.

What helps, once the wall is dry: an alkali-resistant primer on repaired plaster, which stops the salts in fresh plaster attacking the topcoat, and Prestige Super Filler for the cracks and hollows left behind, sanded flush before painting.

Prestige Facelift Premium is a sensible finish for the rooms where damp has been a problem, because a harder film that can be wiped gives you a chance to deal with a small recurrence before it spreads.

The patterns that mean “stop”

  • Paint that blisters within weeks of being applied, in the same shape as before
  • A salt bloom returning through a new finish
  • Plaster that sounds hollow when tapped
  • Mould returning in the same corner, in a room that has never had a leak

Each of those means the cause was not fixed, and no amount of extra coats changes it.

Before you buy paint

Tell us where the damp is, when it appears and what it looks like, and we will tell you whether it is a paint problem or a building problem, and what to do first. Call +234 802 562 5333 or message us on WhatsApp.