Most paint is bought by eye. People look at a room, remember roughly what they used last time, and buy two tins more than they needed or one less. The first is wasted money; the second is a second trip and a colour that may not match.
Measuring a room takes ten minutes and a tape, and the arithmetic is simple. The only real risk is measuring the wrong thing.
Measure wall area, not floor area
This is the mistake that starts everything. Floor area tells you how big the room is; wall area tells you how much paint you need. They can differ by a factor of three or four.
A small bedroom with a 3.5 by 4 metre floor has 14 square metres of floor. The same room with a 2.7 metre ceiling has around 40 square metres of wall. Buying on floor area and finding you have a third of what you need is the usual outcome.
The method
- Measure the length of every wall in the room and add them together. That is the perimeter
- Multiply the perimeter by the ceiling height. That gives the gross wall area
- Measure each door and window and multiply width by height. Add those together
- Subtract the openings from the gross wall area
- Measure the ceiling separately, length times width
That is the whole calculation. Everything else is arithmetic.
A worked example
A bedroom 3.5 m by 4 m, with a 2.7 m ceiling, one door and one window.
- Perimeter: 3.5 + 3.5 + 4 + 4 = 15 m
- Gross wall area: 15 × 2.7 = 40.5 m²
- Door: 0.9 × 2.1 = 1.9 m². Window: 1.5 × 1.0 = 1.5 m². Total openings: 3.4 m²
- Net wall area: 40.5 − 3.4 = 37.1 m²
- Ceiling: 3.5 × 4 = 14 m²
Now the coats. Two coats means the paint has to cover the net area twice: 37.1 × 2 = 74.2 m² of wall, plus 14 × 2 = 28 m² of ceiling.
Then divide by the coverage figure printed on the tin. If the tin says the product covers 12 m² per litre, the walls need about 6.2 litres and the ceiling about 2.3 litres. Round up, and buy in the tin sizes available.
Note the number that did the damage: 12 litres of paint for a room that has 14 square metres of floor.
Where estimates go wrong
Underestimating coats. One coat is not an option for a colour change or a new surface. Two is the minimum, and three is normal when going from dark to light.
Forgetting the ceiling. Ceilings are a large flat area and are usually included in a room repaint. Leaving them out of the calculation is the most common reason people run short.
Ignoring texture. Rough or textured surfaces have far more surface area than their flat dimensions suggest, and they absorb more paint. If the wall is textured, add a margin rather than trusting the coverage figure.
Ignoring porosity. New plaster and bare blockwork drink paint. The first coat on a porous surface can disappear, and the coverage figure on the tin assumes a sealed surface.
Forgetting the trim. Doors, skirting and frames are small individually and add up quickly. Measure them or add a sensible allowance.
Do you really need to deduct the openings?
Strictly yes, practically it depends on the size of them. A door or a standard window is a small deduction and many people skip it, accepting a slight over-order as insurance.
Wide windows and sliding doors are different. A two-metre sliding door is over four square metres, and a room with two of them is nearly a tin short if you ignore them. Deduct anything large; ignore the small stuff if you want a margin.
The one thing not to do is deduct an opening and then paint the reveals and the frame surround with the same wall paint. Measure the reveals separately if they are being painted, or leave the opening in the calculation.
Scaling it to a whole flat
The same arithmetic applies room by room, and the totals add up quickly. A three-bedroom flat typically has three bedrooms, a living room, a kitchen, a bathroom and a hallway, and the hallway is often the largest single wall area in the property because it has very little furniture against it.
Work out each room separately rather than estimating the flat as one figure. That way, if money runs short, you can see which rooms are driving the total, and you can decide to do the bedrooms later without recalculating everything.
Add the ceilings to every room, and add the trim as a percentage rather than ignoring it: on a typical flat, doors, frames and skirting can account for a meaningful share of the total paint, particularly if they are changing colour.
Rooms that are not simple rectangles
Most rooms have something awkward:
- Alcoves and bays. Measure each face and add them; do not approximate with the overall width
- Sloped or double-height ceilings. Measure each plane separately. A stairwell can have more wall than three bedrooms
- Built-in wardrobes. If they are staying, deduct the wall they cover; if they are floor-to-ceiling, they may cover a surprising amount
- Air-conditioner units, tiles and panelling. Deduct tiled areas, and leave the wall behind a split unit out of the calculation while it is mounted. Treat panelled walls as a separate job with their own product
Buying in the right batch
Work out the total for the whole job first, then buy it in one purchase. Colour varies slightly between batches, and a wall painted across two batches can show the join.
Buy a little more than the arithmetic says, particularly for dark colours, textured surfaces or a first coat on bare plaster. A spare litre is useful for touch-ups later; running out mid-wall is not.
If you would rather not do the measuring
Send us the room sizes and ceiling heights, or even a rough floor plan, and we will work out the quantities for you and tell you what tin sizes to buy. Call +234 802 562 5333 or message us on WhatsApp.