A kitchen that looks dated usually has sound carcasses and tired doors. Replacing the whole kitchen is expensive and disruptive; painting the doors, drawer fronts and frames is a fraction of the work and can transform the room in a week. The catch is that kitchens are the worst possible environment for paint, and most cabinet repaints fail for one reason: grease.
Paint does not bond to a greasy surface. It sits on top, looks fine for a month, then chips off in sheets from the edges where hands go.
Why kitchens defeat paint
Every surface in a working kitchen carries a film of cooking oil, and that film is invisible. It is also spread by touch, which is why the handles and the edges of doors carry the most. On top of the grease there is steam, heat near the cooker, and constant handling.
Wooden and MDF cabinet doors also move. They expand and contract with humidity, and the joints between a frame and a panel open and close slightly through the year. A rigid, thick paint film on a moving joint cracks; a thin, well-bonded film flexes with it.
So the rules are: remove every trace of grease, key the surface properly, use a primer designed to bond, and apply thin coats rather than thick ones.
Preparation, in order
- Remove doors, drawers, handles and hinges, and label everything so it goes back in the same place
- Degrease every surface with a strong degreaser, working the edges and handles twice. Rinse and let it dry completely
- Sand to a key. On a factory finish this means dulling the sheen everywhere, not stripping it
- Fill dents, old screw holes and chips, then sand flush
- Dust off, then wipe down with a cloth. Filler dust and sanding dust both stop paint bonding
- Prime, then paint within the primer’s recoat window
Work on the doors flat, on trestles, not hung on the carcass. Paint runs on a vertical panel, and a door painted in place will show sags along the bottom rail.
The primer is the whole job
On bare or previously varnished wood, a bonding primer is what holds the topcoat on. On MDF, the cut edges need sealing or they drink paint and stay rough however many coats you apply. On a factory lacquered door, the key you sand into the surface is what the primer grips.
Skipping primer to save a step is the most common cause of a cabinet job that looks good in the photos and peels within a year.
Choosing the finish
Prestige Satin Finish is the sensible default for cabinets: hard enough to wipe, low enough sheen to hide the imperfections in an older door, and it does not show every fingerprint the way gloss does.
Prestige Premium Plus Gloss gives a harder, more traditional finish and is easier to clean, but it shows every dent and brush mark, so it rewards careful preparation and punishes anything rushed. On a flat, modern door in good condition it looks excellent. On an old panelled door with chips and filled repairs, satin hides more.
Whatever you choose, two thin coats beat one thick one. A heavy coat on a vertical door sags, and it stays soft underneath for days.
Brushing, rolling or spraying
Brush and roller is the practical route for most homes in Nigeria, and a small foam roller followed by a brush to lay off the marks gives a decent finish on flat panels.
Spraying gives the smoothest result, but it needs the doors off and laid flat, a dust-free space, and proper masking. In an occupied house the overspray and the smell usually rule it out. If a professional is spraying, the preparation still has to be done to the same standard; spraying a greasy door just makes the peeling look smoother.
Wardrobes are the same job with less grease
Built-in wardrobes and bedroom furniture take the same treatment without the degreasing problem. The prep is sanding and keying, and the main risk is different: dark furniture painted light needs a primer tinted towards the topcoat, or it will take three or four coats to cover.
Inside surfaces are usually left alone. Painting the interior of a wardrobe makes it smell of paint for weeks and gains almost nothing, since nobody sees it once the doors are shut.
Drying, reassembly and the first weeks
Doors need to cure flat and undisturbed. Leave them at least the recoat time stated on the tin, and ideally a full day before refitting. A door refitted while the film is still soft will stick to the frame, and pulling it open takes the paint with it.
Refit the hardware only when the paint is properly hard. Handles tightened onto soft paint leave a ring that never settles.
Do not wash the cabinets for a couple of weeks. A paint film hardens over days, not hours, and washing early dulls a satin or gloss finish and shortens its life.
What this job will not fix
Paint covers the surface, not the structure. If the carcasses are swollen from a leak, if the hinges have torn out of the chipboard, or if the doors are warped, painting them makes a broken kitchen look freshly painted. Those problems are worth fixing first, or the money is better spent replacing.
It also will not change the layout, the worktop or the tiles. A cabinet repaint is worth doing when the units are sound, the doors are flat and the room simply feels tired.
Getting the products right
Tell us how many doors and drawers, what they are made of and what finish is on them now, and we will tell you what primer and topcoat the job needs, and roughly how much. Call +234 802 562 5333 or message us on WhatsApp.