Sooner or later every repaint meets an old finish that refuses to take new paint. It might be gloss on the skirting, a silk emulsion on the walls that feels almost like plastic, or a previous owner’s attempt at a wipeable surface in a hallway.
The rule underneath all of it is simple: paint grips a surface it can key into. A smooth, sealed film gives it nothing to hold, and the new coat sits on top like a skin until something knocks it.
Work out what you are painting over
Before choosing anything, identify the old finish. Three quick tests settle most cases.
- Rub a cloth with a little detergent. If colour comes off, it is a cheap emulsion and probably not washable
- Look at the sheen. A high shine on trim is gloss or a gloss enamel; a soft sheen on walls is silk or satin
- Scratch a hidden spot with a fingernail. A hard, brittle film that chips is an oil-based gloss. One that rubs or powders is emulsion
That distinction changes the method. Gloss needs keying and usually a primer. Old emulsion mostly needs cleaning and a light sand.
Why new paint fails on gloss
Gloss is designed to be hard, smooth and washable. Those are the qualities that make it a good finish and a bad surface to paint onto. New paint cannot penetrate it, so it forms a film that bonds weakly and fails at the edges first, then in sheets.
The failure usually appears as peeling from the bottom of a door or around a frame, where hands and cleaning cloths work at the edge. Once water gets behind that edge, the whole coat lifts.
The preparation that actually matters
- Wash with a degreaser. Gloss in kitchens and on doors carries grease and hand oils that no paint will bond to
- Rinse and let it dry fully
- Abrade the surface with medium abrasive paper until the sheen is gone. This is the step people skip, and it is the one that decides whether the job lasts
- Dust off thoroughly, then wipe with a damp cloth
- Prime bare or repaired areas, and use a bonding primer over the gloss if it is in good condition
The test for ”abraded enough” is simple: the surface should no longer reflect a sharp highlight. If it still shines, keep going.
Do you need a special primer?
Not always, but on hard gloss it is cheap insurance. A bonding primer gives the topcoat something to grip, and on a surface that has resisted paint before it is worth the extra step.
What does not work is skipping preparation and hoping a primer will compensate. Primer bonds to a keyed surface; it does not create adhesion out of nothing.
When to strip instead
Stripping is the right answer when the old film is already failing. If paint is flaking, blistering or peeling in patches, painting over it simply buries a failing layer that will take the new coat with it.
Strip back to a sound surface where the failure is, feather the edges, fill and prime. On a door with multiple coats of old gloss that has gone brittle, taking it back properly is often faster than fighting it.
Also strip where the buildup is thick enough to have rounded off the detail — the mouldings on a door or the profile of a skirting. Another coat on top softens the shape further, and no amount of paint brings detail back.
The practical trade-off
Keying and priming adds a day to a job. Skipping it saves that day and risks the whole room within a year, which is a bad trade at any price.
Where the old finish is sound and simply the wrong colour, prepare properly and paint over it. Where it is failing or has been applied too thickly, strip it. Those are the only two sensible options; painting over a failing film is not a third.
Finish choice on top
Once the surface is keyed and primed, you are free to choose. On trim and doors, Prestige Satin Finish gives a tough, wipeable film with less glare than gloss, and it shows brush marks far less — which matters on a large flat door panel.
On walls, a matt or mid-sheen finish covers better over an old colour and hides the unevenness underneath. On any filled or repaired area, Prestige Super Filler sanded flush and primed will disappear; unprimed filler will not.
Working out what your walls need
Tell us what the old finish is, how many coats are on it and whether it is sound, and we will tell you whether to key and paint or strip back. Call +234 802 562 5333 or message us on WhatsApp.