A leak is over in an hour. The wall takes months. Most repaints after a burst pipe or a roof leak fail not because the paint was wrong but because the wall was painted while it was still wet inside, or because the stain was never blocked and came back through the new coat within a week.
The sequence below is the one that works. It is slower than painting over the mark, and it is the only way the mark stays gone.
First, confirm the leak has actually stopped
This sounds obvious and it is the step most often skipped. A roof leak can stop raining and still be feeding water through a soaked ceiling for days. A pipe repair can leave a section of wall saturated long after the joint is dry.
Before anything else: check the source is fixed, not just quiet. If a plumber has been in, ask what was replaced and whether anything is still weeping. If it was the roof, wait for a dry spell and look again.
Dry the wall, properly and patiently
Plaster holds a surprising amount of water. It will look dry on the surface within a day or two while the middle is still wet for weeks.
Speed it up with air movement: open windows, use a fan, and keep the room ventilated rather than sealed. Do not use a heater pointed at the wall, which dries the surface hard and traps moisture behind it.
The test that settles it is the same one used on new plaster: tape a square of clear plastic tight to the wall, leave it a day, and look for condensation on the inside. Any moisture means the wall is still releasing water. A moisture meter settles it faster if you can borrow one.
Take off what the water ruined
Water damages plaster in a predictable way: it softens it, then the salts crystallise as it dries, and the surface becomes powdery or blows away from the blockwork.
Tap the affected area. A hollow sound means the plaster has separated and has to come off. Scrape back anything soft or crumbly to sound material, and take the edges back further than the visible stain, because water travels sideways inside the wall.
White salt bloom should be brushed off dry. Washing it back into the wall just returns the salts.
Repair, then let the repair cure
Fill the stripped area with Prestige Super Filler in thin layers rather than one thick one, letting each layer dry. A deep fill applied in one go shrinks, cracks and stays soft in the middle.
Sand flush once fully dry. On a large patch, feather the edges out beyond the repair so there is no ridge to catch the light.
Then wait. Fresh filler and fresh plaster both need to cure, and painting too early is how a repair turns into a blister.
Block the stain before you paint
A water stain is not just discolouration; it is residue that migrates into any new paint film. Ordinary emulsion over a water mark will let it bleed back through, sometimes within days.
Seal the repaired and stained areas with a stain-blocking primer, and extend it beyond the visible edge. This one step is what separates a repair that disappears from a repair that comes back every year.
On a ceiling, do the same. Ceiling stains are the most common comeback in decorating.
Matching the colour
A repaired patch painted with the original paint will often still show, because the wall behind it has faded and the tin has aged. Expect it, and plan for it.
The practical options, in order of how invisible they are:
- Repaint the whole wall, corner to corner. The repair disappears completely
- Repaint to the nearest natural break — a corner, a doorway or a change of plane — rather than stopping mid-wall
- Touch in the patch with the original product, accepting a slight difference that will even out over a few months
What not to do is paint a neat rectangle around the repair. It is more visible than the stain was.
Deal with the smell too
After a leak in a closed room, there is often a musty smell that painting does not remove. It comes from damp in the fabric, not the surface. Ventilation and time fix it; sealing it under paint locks it in.
If the smell persists after the wall is genuinely dry, there is still moisture somewhere — behind a skirting, under a floor, inside a ceiling void. That is worth finding before you finish the room.
The sequence, in short
- Confirm the leak is fixed
- Dry the wall with air movement, and test it
- Strip any blown plaster back to sound material
- Repair in thin layers, sand flush, and let it cure
- Seal stains and repairs with a stain-blocking primer
- Paint the whole wall or to a natural break
Getting the paint right
Tell us what leaked, how long ago, and what state the plaster is in, and we will tell you whether it is ready to paint and what it needs. Call +234 802 562 5333 or message us on WhatsApp.