High humidity in Nigeria is not a seasonal problem. Coastal cities hold moisture for most of the year, and even inland the rainy season puts water into the air for months at a time. Every house has rooms that stay damp: bathrooms, kitchens, laundry areas, and any room built against a shaded external wall.
Paint in those rooms fails differently from paint anywhere else. The film softens, mould grows in it, and it eventually lifts. The fix is part product, part preparation, and part accepting that some of it is a building problem rather than a painting one.
What humidity actually does to a painted wall
Water vapour in warm air condenses on the coolest surface in the room. In a Nigerian house that is usually an external wall, the ceiling above a shower, or a wall behind a wardrobe where air does not move at all.
Once moisture sits on the film, three things happen in sequence. A porous paint absorbs it and softens. Mould spores, which are everywhere, settle in the damp film and grow. Water works its way behind the paint and the film blisters and lifts off the plaster.
By the time you see black spotting or a bubble, the problem has been running for months.
The right finish
Prestige Satin Finish is the correct choice for a high-humidity room. The film is harder and less porous than matt, so moisture sits on the surface rather than soaking in, and it can be wiped when condensation leaves marks.
Matt emulsion is the wrong product here regardless of colour. It absorbs moisture, it cannot be scrubbed without the film breaking down and going shiny in patches, and it will look tired within two years.
For the ceiling in the same room, use a ceiling product — Prestige Best for POP on POP, or a matt ceiling paint on plaster. Steam rises, so the ceiling takes it first.
Mould is a ventilation problem, not a paint problem
No coating prevents mould in a room with no airflow. This is the part people resist, but it is the truth: if a bathroom has no window and no extractor fan, mould will return through any paint you put on the wall.
The permanent fixes are an extractor fan, a window that is actually opened during and after a shower, or a door left ajar so air can move. Where none of those is possible, expect to clean and repaint more often.
Preparation for a humid room
- Wash with a bleach solution to kill the mould, then rinse. Painting over black spotting means it grows through the new film.
- Scrape back anything loose, blistered or flaking to a sound edge.
- Fill cracks and hollows with Prestige Super Filler and sand flush.
- Let the wall dry completely. This is the step that gets skipped. A wall that feels dry to the touch can still be holding moisture a centimetre down, and painting it traps that water.
- Prime bare patches and all repairs.
- Two coats of satin, with the room ventilated and the door open between coats.
Which rooms count
- Bathrooms — the worst case, because of daily steam and splash
- Kitchens — steam plus grease, which is a harder combination
- Laundry and utility rooms — steady moisture with poor airflow
- Rooms on a shaded external wall — often a bedroom that never gets sun and grows mould behind the wardrobe
- Coastal properties — salt air adds to the humidity load on every wall, inside and out
What about the outside of the same wall
If the room is damp because water is coming through the external wall, interior paint will not solve it. Exterior coatings matter here: Prestige Textured Finish puts a thicker, more weather-resistant film on the outside face and bridges the hairline cracks that driven rain finds.
But if the damp is rising from the ground, or a pipe is leaking inside the wall, that is a building repair. Coating over it delays the problem and wastes the paint.
How much paint a humid room needs
A typical 2m by 2m bathroom has a perimeter of 8m, so 21.6 square metres of gross wall at 2.7m ceilings. Deduct a door and a window and you have roughly 17 square metres. At two coats and about 11 square metres per litre per coat, that is just over 3 litres — one 4 litre tin, with enough left for touching up.
Add the ceiling separately. Confirm coverage on the tin you buy; it varies between products.
Mistakes that guarantee a repeat
- Using matt emulsion because it was left over from another room
- Painting over mould without killing it first
- Painting a wall that is still damp from washing
- Skipping primer on new plaster
- Ignoring ventilation and expecting the paint to cope
- Choosing a dark colour, which shows every water mark and every patch of mould
Getting it right
Tell us the room, whether there is a window or an extractor, and what is on the walls now. We will tell you the finish, the quantity and what preparation the room needs. Call +234 802 562 5333, message WhatsApp, or send your project details.